designed and manufactured in germany designed and manufactured in germany AXIOM145ULN rev.3 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 1(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg specification AXIOM145ULN rev.: 3 date: 2017-01-07 oscillator type: ultra-low noise ocxo in smd packag e parameter min. typ. max. unit condition nominal frequency (note 2) 10.000 mhz frequency stability initial tolerance @ +25c 100 ppb v c @ vref/2 vs. operating temperature range option 2 & 3 see tables 2 & 3 steady state vs. supply voltage variation (pushing) 0.5 ppb v s 100 mv vs. load change (pulling) 0.5 ppb r l 5 % long term (aging) per day 0.5 ppb after 10 days operation long term (aging) 1 st year 30 ppb after 10 days operation long term (aging) 15 years 500 ppb after 1 0 days operation frequency adjustment range electronic frequency control (efc) 0.5 1.0 1.5 p pm efc voltage v c 0 vref/2 vref v efc slope positive efc non-linearity 10 % efc input impedance 100 k modulation bandwidth 1 khz @ -3 db rf output signal waveform sine wave load r l 50 5 % output level +5 +10 dbm harmonics -20 dbc spurious -90 dbc @ 9 ~ 11 mhz warm-up time @ +25c 5 min ? f final /f nominal < 100 ppb phase noise see table 1 option 1 short term stability (allan deviation) 110 -11 510 -12 110 -11 110 -10 = 1 s = 10 s = 100 s oven alarm output low = alarm (not stable) high = ready 0 0.4 v 2.4 5 v oscillator enable input (note 3) low = oscillator off high = oscillator on 0 0.4 v 2.4 12.6 v reference voltage vref output 5.0 v supply voltage v s 10.5 12.0 12.6 v current consumption (steady state) 200 ma @ +25c current consumption (warm-up) 340 ma marking axtal logo AXIOM145ULN 10.000mhz s/n wwyy ww = week, yy = year enclosure (see drawing) (lxwxh) 41x30x16 max. mm weight 30 g packing palette notes: 1. terminology and test conditions are according to ie c60679-1 and mil-prf-55310, unless otherwise stated 2. other frequencies on request 3. hcmos compatible input
designed and manufactured in germany designed and manufactured in germany AXIOM145ULN rev.3 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 2(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg absolute maximum ratings parameter min. max. unit condition supply voltage v s -0.5 v s + 10% v v s to gnd control voltage v c -0.5 15 v v c to gnd oscillator enable voltage v oe -0.5 v s v v oe to gnd storage temperature -55 +125 c resistance to soldering heat 10 sec @ +245c phase noise C option 1: option offset a b c unit 1 hz -110 -112 -115 dbc/hz 10 hz -142 -144 -146 dbc/hz 100 hz -155 -156 -157 dbc/hz 1 khz -160 -160 -160 dbc/hz 10 khz -165 -165 -165 dbc/hz table 1 frequency stability vs. temperature C options 2 & 3 stability lower temperature upper temperature option 2 [ppb] option 3 t [c] option 3 t [c] 05 5 0 0 a +50 10 10 1 -10 b +60 25 25 2 -20 c +70 50 50 3 -30 d +75 100 100 4 -40 e +80 200 200 5 -55 f +85 table 2 table 3 standard: 1b = -10c to +60c frequency stability [option 2] temperature range [c] 05 10 25 50 100 200 0 ~ +50 x x x x x x -10 ~ +60 x x x x x x -20 ~ +70 x x x x x x -30 ~ +70 o x x x x x -40 ~ +75 o o x x x x -40 ~ +85 o o x x x x -55 ~ +85 - o o x x x table 4 availability x = available, o = available on request, - not availa ble ordering code model option 1 [phase noise] option 2 [stability] option 3 [temperature range] revision frequency [mhz] AXIOM145ULN table 1 table 2 table 3 rev.3 10.000 example: AXIOM145ULN-a-50-1b_rev.3 C 10.000 mhz
designed and manufactured in germany designed and manufactured in germany AXIOM145ULN rev.3 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 3(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg handling and testing parameter procedure source handling and testing application note axan-011 www. axtal.com processing application note axan-012 www.axtal.com parameter procedure condition electrostatic discharge (esd) thd devices iec60749-26 hbm 2000 v smd devices iec60749-27 mm 200 v washable yes no rohs- compliant yes no enclosure drawing: pin connections pin # symbol function 1 rf out rf output 2 oa oven alarm output 3 gnd ground 4 vref reference voltage 5 v c control voltage (efc) 6 oe oscillator enable input 7 v s supply voltage
designed and manufactured in germany designed and manufactured in germany AXIOM145ULN rev.3 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 4(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg environmental conditions test iec 60068 part iec 60679-1 clause mil-std- 202g method mil-std- 810f method mil-prf- 55310d clause test conditions (iec) sealing tests (if applicable) 2-17 5.6.2 112e 3.6.1.2 gross leak: test qc, fine leak: test qk solderability resistance to soldering heat 2-20 2-58 5.6.3 208h 210f 3.6.52 3.6.48 test ta method 1 test td 1 method 2 test td 2 method 2 shock* 2-27 5.6.8 213b 516.4 3.6.40 test ea, 3 x pe r axes 100g, 6 ms half-sine pulse vibration, sinusoidal* 2-6 5.6.7.1 201a 204d 516.4-4 3.6.38.1 3.6.38.2 test fc, 30 min per axes, 10 hz - 55 hz 0,75mm; 55 hz - 2 khz, 10g vibration, random* 2-64 5.6.7.3 214a 514.5 3.6.38.3 3.6.38.4 test fdb endurance tests - ageing - extended aging 5.7.1 5.7.2 108a 4.8.35 30 days @ 85c, ocxo @25c 1000h, 2000h, 8000h @85c other environmental conditions on request data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. revision history rev. drawing date [dd.mm.yyyy] remarks author checked 1 d0 10.12.2013 first issue preliminary version axi om15uln hh bn 2 d0 12.12.2013 changes: operating temp rang, suppl y voltage. added: modulation bandwidth hh bn 1 d0 03.02.2014 new package, new p/n AXIOM145ULN hh bn 1 d1 16.01.2015 editorial changes, environmental ch anges updated hh hh 2 d0 11.01.2016 phase noise options added hh hh 3 d0 07.01.2017 temperature stability options added bn bn
|